The replacement logic board will provide obstruction notifications once it is installed. If the door makes contact with an obstruction while opening, the door will stop, the opener will beep and the lights will flash five (5) times. When the door is in any position other than closed and the garage door opener is activated, the door will close.Step 2: Check that the Sensors Are Aligned. Garage door sensors are either sending sensors or receiving sensors. The sending sensor has a yellow or orange LED light that should always be viable. The receiving sensor has a green or red LED light that will only be visible when functioning correctly.11 Reasons Why Your Automatic Garage Door Won't Open (or Shut) The photo eye is blocked. Its power source is disrupted. The torsion springs are broken. Remote control malfunction. Snapped or loose cables. Sensitivity needs adjustment. The limit setting is off. The door has dislodged from its track.This is to check whether the issue lies with the garage door itself, or the garage door opener. If you can open the door, then the door is not at fault. Instead, you’ll need to investigate the garage door opener. If the door won’t open, then it’s the door itself which is causing the problem. Related: How to Open a Garage Door with a ...Blinking/Flashing. Blue and Green. One (1) beep. Unable to connect to your home Wi-Fi router. Unable to Connect the Wi-Fi Garage Door Opener to Wi-Fi Network and LED Lights Flash Blue and Green. Blinking/Flashing Green. Two (2) beeps. Unable to connect to myQ internet server.Allow the motor to cool for about 15 minutes before restoring power and using the garage door opener. Pull the emergency door release and check the up-and-down travel of the garage door for binding. Repair the garage door if it doesn't travel smoothly. If it overheats after a single use and the garage door travel is smooth, replace the motor.The garage door won’t open with wall switch The following process describes a detailed diagnosis of a garage door that cannot open with a wall switch; Step 1. Test the power outlet. Unplug the opener from the outlet. Take a cellphone charger, plug your phone in, and plug it into the outlet to your garage door opener was connected.Blinking/Flashing. Blue and Green. One (1) beep. Unable to connect to your home Wi-Fi router. Unable to Connect the Wi-Fi Garage Door Opener to Wi-Fi Network and LED Lights Flash Blue and Green. Blinking/Flashing Green. Two (2) beeps. Unable to connect to myQ internet server.Leave the myQ app and go to your phone's Wi-Fi settings. Tap the network that begins with myQ- XXX. Return to the myQ app and tap Next. Select your home Wi-Fi network from the list. Enter your network password and tap Next. Your garage door opener is now connecting. Name your garage door opener and tap Next. Dec 10, 2021 · Garage doors can have all sorts of wonky problems. You might find your garage door is opening itself or the garage door won't open with the remote. But when your auto-reverse feature isn't working correctly, you really have a problem. Use the following tips to adjust the settings. 1. Test the Auto-Reverse Function Dec 1, 2020 · This video demonstrates what to do if your Chamberlain garage door won't fully open. Your garage door is designed to stop if it senses resistance or an obstr... the yellow antenna for about 7 seconds until the led near it turns on and turns. back off then release the yellow button. You want to repeat this 3x in a row the opener should beep when successfully. cleared. Note the accessories like remotes and keypad anything wireless will need to be. reprogrammed to the opener.Here is all you need to do; Detach the wall control unit from the wall and then disengage the wires linking the wall control at the back. This is the test step. Bring the bare ends of the disconnected wall console wires into contact and observe whether the garage door moves. There are also two possible outcomes; Find the Chamberlain garage door opener technical support you need to help fix any issues you may be having with your garage door opener and parts. From informational videos to product manuals and troubleshooting articles, the Chamberlain Group resource library has the information you need. Locate the myQ app and open it. Inside the folder you will find storage options. Once you’ve clicked on it, the Clear All Data button should appear. Simply press it and launch the myQ app again. After that try to connect your myQ hub to your mobile app again to see if the issue has been resolved. 2.Apr 14, 2012 · Garage door not closing? Easy fix!!Safety sensors are the number one component that will cause a garage door not to close. Do you hear 10 clicks or the lig... The garage door won’t open with wall switch The following process describes a detailed diagnosis of a garage door that cannot open with a wall switch; Step 1. Test the power outlet. Unplug the opener from the outlet. Take a cellphone charger, plug your phone in, and plug it into the outlet to your garage door opener was connected. Find the Chamberlain garage door opener technical support you need to help fix any issues you may be having with your garage door opener and parts. From informational videos to product manuals and troubleshooting articles, the Chamberlain Group resource library has the information you need. The chart below is a quick reference on what your garage door opener’s blinks mean: A safety sensor wire may be open, broken, or disconnected. A sensor wire is either shorted, or the wires could be reversed. The door control or wire is shorted. The safety sensors are misaligned, which breaks the electronic beam, preventing the garage door ... In case you cannot find this control, make sure to check the garage door manual, or contact a professional. 5. Faulty Garage Door Opener. As the name itself implies, garage door openers are responsible for opening your garage door. In this case, the issue could be in the sensitivity of the garage door opener and it may have to be adjusted.Using a flat screwdriver, twist the “down” screw in quarter-turn increments, checking how your garage door operates between adjustments. Adjust it until the door closes all the way and compresses the rubber seal slightly. If the door closes and bounces back open, back the “down” adjustment off. 6. Check Your Manual. A caution here. Not sure what brand garage door opener is talked about here. I have a Genie door opener and installation manual for the wall button has in "WARNING!! in BIG BOLD letters saying "Be sure Wire ends do not touch each other or other Terminals."Dec 1, 2020 · This video demonstrates what to do if your Chamberlain garage door won't fully open. Your garage door is designed to stop if it senses resistance or an obstr... If you are having trouble pairing your garage door opener with a RED/ORANGE learn button , choose the GREEN button option when going through the in-app setup. In some instances, interference may occur when the hub has been installed too close to the motor unit. Unplug the hub and move it at least 4-6 feet away from the motor-head.Allow the motor to cool for about 15 minutes before restoring power and using the garage door opener. Pull the emergency door release and check the up-and-down travel of the garage door for binding. Repair the garage door if it doesn't travel smoothly. If it overheats after a single use and the garage door travel is smooth, replace the motor.The Chamberlain Group LLC, the corporate parent company to LiftMaster, Chamberlain, Merlin and Grifco, is a global leader in access solutions and products. We design and engineer residential garage door openers, commercial door operators and gate entry systems. The Down Travel Needs to be Adjusted. The steps to adjust the travel vary by model. Reference the articles listed below for assistance with making adjustments. How To Adjust The Limit Or Travel On A Garage Door Opener With Manual Adjustment Screws. How To Program The Travel Limits on Garage Door Opener Models 3500D, 3500C, HD800D, WD952KCD ...With the door disconnected, run the opener with the remote or door control. Listen for any excessive noise from the opener. If the opener is noisy without the door, check the drive tension. Chain drive models - Check for proper tension on the chain. Belt drive models - Check for proper tension on the belt.If you hear a beep, tap Yes. Apple users: Tap Join to connect to the network myQ-NNN. Android users go to step 11. Select your home Wi-Fi network from the list. Enter your network password and tap Next. Your garage door opener is now connecting. Tap Finish on the success screen. Go back to the Devices screen.This is to check whether the issue lies with the garage door itself, or the garage door opener. If you can open the door, then the door is not at fault. Instead, you’ll need to investigate the garage door opener. If the door won’t open, then it’s the door itself which is causing the problem. Related: How to Open a Garage Door with a ...Find the Chamberlain garage door opener technical support you need to help fix any issues you may be having with your garage door opener and parts. From informational videos to product manuals and troubleshooting articles, the Chamberlain Group resource library has the information you need. Leave the myQ app and go to your phone's Wi-Fi settings. Tap the network that begins with myQ- XXX. Return to the myQ app and tap Next. Select your home Wi-Fi network from the list. Enter your network password and tap Next. Your garage door opener is now connecting. Name your garage door opener and tap Next. Types of Obstruction Symptoms. If the door makes contact with an obstruction while opening, the door will stop, the opener will beep and the lights will flash five (5) times. When the door is in any position other than closed and the garage door opener is activated, the door will close. If the garage door makes contact with an obstruction while ...Lex20 / Getty Images. If the garage door won't open, sometimes the reason is that the door is off track due to a loose track. The problem may be preceded by balky or slow movement or by squeaks and unusual noises. To get a garage door back on track, loosen the screws that hold the track to its frame.Chamberlain Group wants to help you seamlessly fix any garage door issues you might be having. Use one of our troubleshooting guides to get your garage door opener working again. Learn what to do if your garage door opener hums but won’t open at all. Or maybe your garage door opener starts to close then goes back up.Feb 6, 2022 · This button is to prevent the door from opening or closing using the hand-held remote. To determine if this is the issue, press the garage door button on the garage wall. Most wall controls will have a light indicating if the lock-out button is on. If you see that the button is activated, you should disengage it. If you are having trouble pairing your garage door opener with a RED/ORANGE learn button , choose the GREEN button option when going through the in-app setup. In some instances, interference may occur when the hub has been installed too close to the motor unit. Unplug the hub and move it at least 4-6 feet away from the motor-head. Chamberlain Garage Door Opener (13) LiftMaster Garage Door Opener (11) myQ Accessories (10) FAQ (1) Show more; Results 1-20 of 189. No Results Found.With the door disconnected, run the opener with the remote or door control. Listen for any excessive noise from the opener. If the opener is noisy without the door, check the drive tension. Chain drive models - Check for proper tension on the chain. Belt drive models - Check for proper tension on the belt. How to Set Up a Chamberlain Secure View Belt Drive Wi-Fi Garage Door Opener in the myQ App. This video is intended for demonstration purposes only. Please consult the manual for complete instructions and safety information. ... 1:55 Connecting your garage door opener to Wi-Fi. Channel: Chamberlain Support Length: 04:29.Unplug the opener and reconnect the wires to the red and white terminals or #1 and #2 screw terminals.Go to the door control, take the door control off the wall by popping off the push button. There is a screw under the push button that holds the door control on the wall. Remove the wires from the back of the door control.Test the remote controls.If the light is still not coming on, it could be the light socket or the logic board. To determine which one it is, follow the steps below. Unplug the garage door opener, then immediately plug the opener back into the electrical outlet. Listen for the light relay on the logic board to click. If you hear a click, replace the light socket. 8. Activated Lock-Out Button. The purpose of a garage lock-out button is to prevent the garage door from being activated by a wireless controller (like the remote). If this button is engaged when you’re attempting to use the remote, it’s going to cause issues whenever the garage door tries to open or close. Using a flat screwdriver, twist the “down” screw in quarter-turn increments, checking how your garage door operates between adjustments. Adjust it until the door closes all the way and compresses the rubber seal slightly. If the door closes and bounces back open, back the “down” adjustment off. 6. Check Your Manual.Jul 18, 2023 · Lex20 / Getty Images. If the garage door won't open, sometimes the reason is that the door is off track due to a loose track. The problem may be preceded by balky or slow movement or by squeaks and unusual noises. To get a garage door back on track, loosen the screws that hold the track to its frame. Nov 16, 2005 · Garage Door in question: Chamberlain 41A5021-1E ½ HP Security +. Problem: With the open/closing button mounted on the wall, it has started not closing unless you keep the button pushed down until it is closed completely. At any time during the closing, you release the button, it will reverse and open right back up. BTW, it opens with no problems. The Chamberlain Group LLC, the corporate parent company to LiftMaster, Chamberlain, Merlin and Grifco, is a global leader in access solutions and products. We design and engineer residential garage door openers, commercial door operators and gate entry systems. 8. Activated Lock-Out Button. The purpose of a garage lock-out button is to prevent the garage door from being activated by a wireless controller (like the remote). If this button is engaged when you’re attempting to use the remote, it’s going to cause issues whenever the garage door tries to open or close. Explore articles, videos, manuals and more to get the most out of your LiftMaster garage door opener remote. From programming to troubleshooting, we're here to help.Besides @longneck's excellent points, if the garage door or opener is a new installation and has not worked before, it could be that the opener's internal "tension sensor" is not correctly set. If the door can be reasonably easily opened and closed by hand, but the opener balks at closing the door, the tension setting probably needs to be ...My Garage Door Won't Open All the Way What to Do When Your Garage Door Won't Open All the Way Your garage door opener features adjustable travel and force settings. Travel adjustment allows you to set where the door stops in the up and down position.Besides @longneck's excellent points, if the garage door or opener is a new installation and has not worked before, it could be that the opener's internal "tension sensor" is not correctly set. If the door can be reasonably easily opened and closed by hand, but the opener balks at closing the door, the tension setting probably needs to be ...Make sure to consult the remote control's owner's manual for additional instructions. Prior to programming a remote control, make sure to clear the garage door area of any obstructions. Program Using Your Garage Door Opener LEARN Button Locate the LEARN button on the garage door opener.Press and immediately release the LEARN button.Dec 19, 2019 · 1. Garage Door Opener Model: Lift-master 1245R (by Chamberlain) Ok, so this has been quite the puzzle. Roughly a couple of months ago, one of my parents' garage door openers started having problems. The problem was that the garage door seemed to open, but not close when using the remote (it worked fine with the wall button). Dec 21, 2022 · Frequency Interference issues with Craftsman, Chamberlain or Liftmaster garage door openers that were manufactured between 1998 and 2010 (with a red, orange or purple smart learn button), can be solved with upgrading the opener to myQ security+ 2.0 system that works on Tri-Band technology and frequencies of 310, 315 and 390 MHz. If you're Craftsman, Chamberlain, etc garage door opener is closing and then opening up - its likely a common problem related to the stop limit mechanism. He...3. Try The Door Control Panel. If your door control has multiple functions, check the “Light” button on the panel. Your door control panel is usually on the wall inside your garage. Sometimes the “Light” switch button is accidentally activated which causes the light to stay on. Try pressing it again to turn it off. How To Troubleshoot ...If the garage door opener button did not work and you do not have a yellow learn button LiftMaster or Chamberlain garage door opener, then you have a bad circuit board and should move to step 4. With a yellow learn button opener, if the wall control LED lit up when you hooked up the jumper wire but nothing happened, bad logic board.Allow the motor to cool for about 15 minutes before restoring power and using the garage door opener. Pull the emergency door release and check the up-and-down travel of the garage door for binding. Repair the garage door if it doesn't travel smoothly. If it overheats after a single use and the garage door travel is smooth, replace the motor.Jun 19, 2020 · If you suspect that your garage door opener may have been affected by a thunderstorm or lightning, give us a call. Circuit boards can run about $100 per board, which is not cheap! But it's less expensive than replacing the entire unit. Give John a call at 864-506-6735 if you suspect that you need a new circuit board. Besides @longneck's excellent points, if the garage door or opener is a new installation and has not worked before, it could be that the opener's internal "tension sensor" is not correctly set. If the door can be reasonably easily opened and closed by hand, but the opener balks at closing the door, the tension setting probably needs to be ... Chamberlain Garage Door Opener (13) LiftMaster Garage Door Opener (11) myQ Accessories (10) FAQ (1) Show more; Results 1-20 of 189. No Results Found. 1. Check for an Obstruction. If there is an obstruction such as cardboard, a crawling child, a pet, or an object on your garage door’s path, the door will reverse its direction when you attempt to close it. The garage door won’t stay or reach its closed position. The presence of an obstruction underneath the door is one of the most likely ...Mar 26, 2019 · This is to check whether the issue lies with the garage door itself, or the garage door opener. If you can open the door, then the door is not at fault. Instead, you’ll need to investigate the garage door opener. If the door won’t open, then it’s the door itself which is causing the problem. Related: How to Open a Garage Door with a ... Make sure to consult the remote control's owner's manual for additional instructions. Prior to programming a remote control, make sure to clear the garage door area of any obstructions. Program Using Your Garage Door Opener LEARN Button Locate the LEARN button on the garage door opener.Press and immediately release the LEARN button.Here is all you need to do; Detach the wall control unit from the wall and then disengage the wires linking the wall control at the back. This is the test step. Bring the bare ends of the disconnected wall console wires into contact and observe whether the garage door moves. There are also two possible outcomes; Dec 20, 2014 · As most garage door remotes work only about 20 feet from the opener, this unit will make it so you can open your garage from up to 100 yards away. This unit is called the Liftmaster 850LM Universal Gate and Garage Door Opener Receiver and is available for right around $40 dollars and WILL solve your garage door opening issues. I installed a new Chamberlain B4505T garage door opener. When I press the open button the lights blink twice and nothing happens. The sensors seem to be installed correctly. There is an amber light in one and a green light in the other. If I block the beam the green light goes out. Does anyone have any idea of what could be wrong?A circuit board with a service light is located on the rear of the motor. The garage door opener service light blink rate indicates various problem codes. Older units will show this: 1 blink – sensor wire is disconnected. 2 blinks – sensor wire are shorted. 3 blinks – sensor eyes misaligned. Newer units with arrow light up buttons.How to Set Up a Chamberlain Secure View Belt Drive Wi-Fi Garage Door Opener in the myQ App. This video is intended for demonstration purposes only. Please consult the manual for complete instructions and safety information. ... 1:55 Connecting your garage door opener to Wi-Fi. Channel: Chamberlain Support Length: 04:29.Jan 28, 2023 · Step 3: Apply Lubricant. Cold weather can lead to parts of your garage door expanding or contracting, which can cause the parts to grind together instead of moving smoothly. You will need to add lubricant to your garage door’s moving parts to keep them from getting stuck. You should apply grease or oil to moving parts such as hinges, rails ... Jan 27, 2022 · A 9V battery powers most outside keypads. Yes, your outside keypad has a battery. If your outside keypad is not working, the first thing you want to check is the battery. The easiest way to tell if your battery needs replacement is if the backlight is not shining. The backlight is what lights up the keys, so you can see them at night. Explore articles, videos, manuals and more to get the most out of your LiftMaster garage door opener remote. From programming to troubleshooting, we're here to help.Lock Mode. When the garage door opener is in lock mode, the LED light on the door control will constantly flash and the hand held remote controls will not operate your garage door opener. The light bulb on the opener will also flash twice when you attempt to activate the door with your remote. To take the unit out of lock mode, press and hold ... With the door disconnected, run the opener with the remote or door control. Listen for any excessive noise from the opener. If the opener is noisy without the door, check the drive tension. Chain drive models - Check for proper tension on the chain. Belt drive models - Check for proper tension on the belt. When you see your garage door opener lights flashing and the garage door will not close, it could be the safety reversing sensors or the LOCK button.; If there is a safety reversing sensor issue, the main light (s) flash 10 times. Start with aligning the safety sensors. Note : You can close the garage door by pressing and holding the door ... Jan 23, 2021 · Here are the ones to recognize: Code 1: Safety sensors aren’t aligned properly or even blocked completely. Code 2: The sensors aren’t wired correctly. Code 3: The door control and/or wires aren’t connected. Code 4: The sensors aren’t working part of the time. Code 5: The system can’t detect any RPM activity. The garage door won’t open with wall switch The following process describes a detailed diagnosis of a garage door that cannot open with a wall switch; Step 1. Test the power outlet. Unplug the opener from the outlet. Take a cellphone charger, plug your phone in, and plug it into the outlet to your garage door opener was connected.4) Follow the prompts and first try to Change or update the Wi-Fi settings, if it doesn't work, erase the settings and start again. 5) Once myq is connected to network, follow the instructions to connect to overhead garage opener.The chart below is a quick reference on what your garage door opener’s blinks mean: A safety sensor wire may be open, broken, or disconnected. A sensor wire is either shorted, or the wires could be reversed. The door control or wire is shorted. The safety sensors are misaligned, which breaks the electronic beam, preventing the garage door ... In case you cannot find this control, make sure to check the garage door manual, or contact a professional. 5. Faulty Garage Door Opener. As the name itself implies, garage door openers are responsible for opening your garage door. In this case, the issue could be in the sensitivity of the garage door opener and it may have to be adjusted.
With the door disconnected, run the opener with the remote or door control. Listen for any excessive noise from the opener. If the opener is noisy without the door, check the drive tension. Chain drive models - Check for proper tension on the chain. Belt drive models - Check for proper tension on the belt. . Apartments in gilbert az under dollar1000
The Down Travel Needs to be Adjusted. The steps to adjust the travel vary by model. Reference the articles listed below for assistance with making adjustments. How To Adjust The Limit Or Travel On A Garage Door Opener With Manual Adjustment Screws. How To Program The Travel Limits on Garage Door Opener Models 3500D, 3500C, HD800D, WD952KCD ... If you are having trouble pairing your garage door opener with a RED/ORANGE learn button , choose the GREEN button option when going through the in-app setup. In some instances, interference may occur when the hub has been installed too close to the motor unit. Unplug the hub and move it at least 4-6 feet away from the motor-head. If the light is still not coming on, it could be the light socket or the logic board. To determine which one it is, follow the steps below. Unplug the garage door opener, then immediately plug the opener back into the electrical outlet. Listen for the light relay on the logic board to click. If you hear a click, replace the light socket.If your garage door opener won’t work even after resetting the remote, you may need to replace it. Clean the photo eye. The photo eye, a small sensor, hovers 4 to 8 inches above the floor on the ...Dec 31, 2020 · Step 4 - Check Obstacle Sensors. Although four (instead of five) flashes typically indicates an issue with the sensors, it’s worth taking a quick look to see if it resolves the issue. Check the sensors located on either side of the door opening, near the bottom. If either one is blinking, that will stop the door from closing and cause it to ... Feb 26, 2015 · How to Disengage and Reengage your garage door opener if you need to open your door manually. The chart below is a quick reference on what your garage door opener’s blinks mean: A safety sensor wire may be open, broken, or disconnected. A sensor wire is either shorted, or the wires could be reversed. The door control or wire is shorted. The safety sensors are misaligned, which breaks the electronic beam, preventing the garage door ... Dec 20, 2014 · As most garage door remotes work only about 20 feet from the opener, this unit will make it so you can open your garage from up to 100 yards away. This unit is called the Liftmaster 850LM Universal Gate and Garage Door Opener Receiver and is available for right around $40 dollars and WILL solve your garage door opening issues. Blinking/Flashing. Blue and Green. One (1) beep. Unable to connect to your home Wi-Fi router. Unable to Connect the Wi-Fi Garage Door Opener to Wi-Fi Network and LED Lights Flash Blue and Green. Blinking/Flashing Green. Two (2) beeps. Unable to connect to myQ internet server.Nov 16, 2022 · Get A New Light Bulb. The simplest fix to Chamberlain garage door opener lights not working is the installation of a new light bulb in the unit. If the bulb was working perfectly just a few days ago, and you’ve had no issues for months, then the bulb has likely gone bad. There isn’t much that you can do about this situation with the light ... Garage door not closing? Easy fix!!Safety sensors are the number one component that will cause a garage door not to close. Do you hear 10 clicks or the lig...See full list on garageadviser.net Using a flat screwdriver, twist the “down” screw in quarter-turn increments, checking how your garage door operates between adjustments. Adjust it until the door closes all the way and compresses the rubber seal slightly. If the door closes and bounces back open, back the “down” adjustment off. 6. Check Your Manual. The Chamberlain Group LLC, the corporate parent company to LiftMaster, Chamberlain, Merlin and Grifco, is a global leader in access solutions and products. We design and engineer residential garage door openers, commercial door operators and gate entry systems.Dec 31, 2020 · Step 4 - Check Obstacle Sensors. Although four (instead of five) flashes typically indicates an issue with the sensors, it’s worth taking a quick look to see if it resolves the issue. Check the sensors located on either side of the door opening, near the bottom. If either one is blinking, that will stop the door from closing and cause it to ... As most garage door remotes work only about 20 feet from the opener, this unit will make it so you can open your garage from up to 100 yards away. This unit is called the Liftmaster 850LM Universal Gate and Garage Door Opener Receiver and is available for right around $40 dollars and WILL solve your garage door opening issues.Jan 23, 2021 · Here are the ones to recognize: Code 1: Safety sensors aren’t aligned properly or even blocked completely. Code 2: The sensors aren’t wired correctly. Code 3: The door control and/or wires aren’t connected. Code 4: The sensors aren’t working part of the time. Code 5: The system can’t detect any RPM activity. 2. Remote Signal Disrupted. After placing fresh batteries in your remote, if the door still won’t respond, then the signal between the remote and opener transmitter may be disrupted. Two common causes for a signal interruption is if your remote is out of range or the opener receiving antennae is damaged. Stand within 20 feet of your garage ... Chamberlain Lift Master Garage Door Opener Troubleshooting. If your garage door opener clicks and doesn't move the door. You have a circuit board issue. M...In case you cannot find this control, make sure to check the garage door manual, or contact a professional. 5. Faulty Garage Door Opener. As the name itself implies, garage door openers are responsible for opening your garage door. In this case, the issue could be in the sensitivity of the garage door opener and it may have to be adjusted. .
Popular Topics
- ArchiveproducttemplatescompatibilityWhat is the number to conn
- TheDodge challenger for sale under dollar5000 near me
- Delta 8 gummies legalAmc dollar2 tuesday
- Ktkl 117Aol news sports weather entertainment local and lifestyle
- Ivy menSub zero ice services inc
- Golden corral buffet and grill kennesaw photosProject
- Hands towing service incGhcea